"Prewired" 14" Rise 1.5" Diameter Chrome "ABS" Big Daddy Bar Complete Handlebar Kit for 2008-2013 FLH Harley Touring

Prewired 14" Rise 1.5" Diameter

Chrome Meathook Bagger Bars 14" ABS Handlebar Kit  

2008-2013 Harley Davidson FLH

Street Glide/Electra Glide/Ultra Limited/Tri Glide 

With the 2008-2013 Harley-Davidson Touring Bikes, the ability to purchase “prewired” bars is typically extremely expensive. The wiring for your stock switches is actually hardwired into your controls and doesn’t allow for the same solution that is available with the late model touring line. Based on this we were able to come up with a solution that is far less difficult and time consuming than extending and snaking your existing harnesses. You are able to utilize our “Prewired” bars with your existing stock switches. We provide the bars prewired with the control wiring and pre-soldered/heat shrink connectors. You will simply cut your control wires, strip a small portion, place them into our pre-soldered/heat shrink connectors and shrink them. With this process we have done the hard work for you, leaving you with just the finishing touches. Thus virtually, making these bars Plug and Play. Finally a “prewired” solution for your 2008-2013 touring model that doesn’t break the bank

Kit Includes:

• 14" Rise 1.5" Diameter Prewired Show Chrome "Big Daddy" Bagger Bars 
• Hydraulic ABS Brake Lines, 1 Upper and 2 Lower Assembly 
  
• Extended Clutch Cable (Hydraulic Line for CVO)
• Control Switch Extensions  
• Electronic Throttle Extension 
• Banjo Bolts and Washers

Handlebar Dimensions:

• 1.5"Bar Diameter
• 36.5" End to End Width
• 14" Rise
• 5.25' Clamping Surface
• 4.5" Pullback

Handlebar Description:

As an Authorized Dominator Industries Dealer We are Proud to Offer Dominator Meathook Bagger Bars for FLH Touring! Dominator Industries bars are carefully designed to provide natural, relaxed grip angles combined with optimal pullback comfort. They are engineered them to be direct bolt-on replacements for stock equipment with No slag inside the bar tubes making installation easier. Laser cut, fully TIG welded, beveled & de-burred for easy internal wire pulling, and polished to a show their quality finish!

Each and every set of Dominator Industries bars are hand-made employing a multi-step manufacturing process using the finest materials. The tube diameter of 1.5” stepped down to 1.25" for fitment with your stock Fairing, also stepped down to 1” for stock/conventional controls. Both grips have 0.5” x 2” slots laser cut for internal wiring. The throttle side is honed out and notched for fly by wire. The Knurled Center for a non-slip grip on our handlebars is engineered to be a direct custom replacement for stock equipment. Proudly offering smooth and clean arched corners, Dominator Industries provides the premium styling distinguishing riders demand.

Cable Description:

For Our Electrical Extensions We Use Special Purpose Automotive Wire that is Insulated with Chemically Cross-Line Polyethylene, Making it resistant to moisture, most solvents, and Gives it the Ability to Withstand Extreme Temperatures. These Features Make Our Wire Ideal for Engine Compartment Applications Where Higher Heat Resistance is Required. 

Our Flexible Polyvinyl Chloride (PVC) Tubing is Designed to Meet the Requirements of MIL-I-631, Grades A & B. This Type of Tubing is used in Appliances, Automobiles, Military Wiring Harnesses and Airborne Equipment. Our PVC Tubing is UV Resistant, Flame Retardant, Lead Free with a High Gloss Black Finish, Making it Perfect for Applications Where a Wide Thermal Range is Required. 

Our Hydraulic Brake Lines and Clutch Cables Meet or Exceed D.O.T. as well as OEM Pressure Specifications. Our Lines are UV Protected Braided Stainless Steel with a Clear Armor Coat Exterior, that Provides Long Lasting Appearance while Protecting Components from Abrasion.

When many aftermarket hydraulic lines are installed, problems can arise from inferior chrome plating. There is nothing worse than rust prone, cheap imitation chrome. Based on this we go the extra mile to achieve a finish that is far superior. Our plating is done here in the US and has been proven to reduce chipping, scratching, rusting or fading. Giving you a product that is not only suitable for practical purposes but will also look great for years to come.